Double click on above image to view full picture

Zoom Out
Zoom In



Cisco Refurbished
Original Part No : 15454-M-RAMAN-CTP=

15454 MSTP-Raman Amp-Cband-CounterPropagating REMANUFACTURED

Availability: In stock

Available Quantity: 66000

Delivery Time: 2 to 4 week

  • Add to Compare
  • Details

    Product Overview

    The Cisco® ONS 15454 Multiservice Transport Platform (MSTP) High-Power Counter-Propagating and Co‑Propagating Raman Amplifiers (Figure 1) operate in the C-band region of the optical spectrum to extend the reach and capacity of regional, long-haul, and ultra-long-haul optical networks beyond what is achievable through standard Raman amplifiers or Erbium Doped Fiber Amplifiers (EDFAs). These cards are part of the Cisco ONS 15454 MSTP intelligent dense wavelength division multiplexing (DWDM) platform, engineered to reduce DWDM complexity and speed the deployment of next-generation networking solutions.

    Supporting 96 channels in the C band, the Cisco ONS 15454 High-Power Counter- and Co-Propagating Raman Amplifiers (15454-M-RAMAN-CTP and 15454-M-RAMAN-COP, respectively) are plug-in modules that provide the reach and optical performance required to meet the most demanding distance requirements of service provider and enterprise DWDM networks.

    Figure 1. Cisco ONS 15454 MSTP High-Power Counter- and Co-Propagating Raman Amplifiers 
    (15454-M-RAMAN-CTP and 15454-M-RAMAN-COP)

    A Raman amplifier uses the intrinsic properties of silica fiber to obtain signal amplification, such that transmission fibers themselves can be used as a medium for amplification, allowing the attenuation of data signals transmitted over the fiber to be mitigated within the fiber itself. An amplifier working on the basis of this principle is commonly known as a distributed Raman amplifier (DRA) or simply a Raman amplifier. The high-power counter- and co-propagating Raman amplifiers are a marked improvement on this technology. In contrast to the standard Raman amplifier where a single counter-propagating Raman pump signal is responsible for the amplification of the traffic signals in the fiber, there are two units: the high power counter-propagating card, which in itself possesses a superior amplification capability compared to a standard Raman amplifier, and a co-propagating Raman card. Together the two units generate Raman pump signals that co- and counter-propagate with the data signal, amplifying it through the Raman effect. Together, the co- and counter-propagating Raman pumps from these units provide amplification to combat signal attenuation in fiber over a much longer distance than previously possible, considerably extending the reach of a single DWDM span.

    As explained in Table 1, two different deployment options are available. One uses the high power counter-propagating unit alone, and the second uses both units, depending on the span length that needs to be traversed.

    Table 1. Cisco ONS 15454 MSTP High-Power Counter- and Co-Propagating Raman Amplifier Deployment Configurations


    Deployment Application

    High power counter- and co-propagating Raman amplifiers (15454-M-RAMAN-CTP and 15454-M-RAMAN-COP) together (master-slave configuration)

    The high power counter-propagating unit injects counter-propagating optical power to generate a Raman effect in the span fiber and thus amplifies the signals propagating in the same fiber. Similarly, the co-propagating Raman unit injects co-propagating optical power that also amplifies the signal through a Raman effect in fiber. The signal thus receives amplification from the optical power injected by both these units present on opposite ends of the span.

    High power counter-propagating Raman unit (15454-M-RAMAN-CTP) alone

    The high power counter-propagating unit injects counter-propagating optical power to generate a Raman effect in the span fiber and thus amplifies the signals propagating in the same fiber.

    Product Overview and Applications

    The high power counter- and co-propagating Raman amplifiers take advantage of the latest in amplifier technology, variable optical attenuators, photo diodes, and extensive software to facilitate a high degree of automation for simplified operations. The Raman pumps embedded in the two units use the latest laser technology, delivering up to 1000 mW of optical power by combining just four pump lasers, thus obtaining a very high efficiency and low power consumption while making possible an extended amplification process for long-haul transmission systems. Figures 2 and 3 show the functional block diagrams of both units.

    Figure 2. Functional Block Diagram for the Cisco ONS 15454 MSTP High-Power Counter-Propagating Raman Amplifier

    Figure 3. Functional Block Diagram for the Cisco ONS 15454 MSTP High-Power Co-Propagating Raman Amplifier

    The counter-propagating Raman amplifier includes an embedded distributed-feedback (DFB) laser at 1568.77 nm to be used for optical safety (link continuity). When loss of signal (LOS) is detected (a related fail-low alarm threshold for a period longer than a preset time span), the DFB laser and Raman pumps automatically shut down for optical safety and automatically restart at detection of valid restart conditions. The shutdown and restart functions can be managed through manual commands from hardware or software, providing an enhanced approach to optical safety. The pumps added from the co-propagating Raman unit to the counter-propagating Raman unit and the associated DFB act in a similar fashion. The counter-propagating unit provides parallel, low failure-in-time (FIT) optical safety functions, which allow the classification of the unit as Class 1M as defined by IEC/EN 60825-1. The embedded detection devices and control mechanisms allow the operator to shut down the amplifier (lowering its transmit optical power below the level defined in the recommendation mentioned previously) if any of the following situations occur:

     Raman pump back-reflection, which may be caused by bad connectors or similar problems with the span fiber

     Detection of open connectors

     Detection of broken fiber up to several tens of kilometers from the node

    The counter-propagating unit allows full monitoring of pump power, signal power, and DFB laser power; whereas only the pump power can be monitored in the co-propagating unit. Both units feature a Raman pump back-reflection detector.

    Due to their potential length, DWDM network spans using Raman amplification may exhibit loss exceeding the reach of the optical supervisory channel (OSC) interface. In these cases, the data-communications-network (DCN) extension capabilities of the Cisco ONS 15454 MSTP can be used to help ensure the correct operation and support of the embedded intelligent optical applications, such as Cisco Wavelength Path Provisioning (WPP), Automatic Power Control (APC), Network Topology Autodiscovery, and Network-Level Alarm Correlation (NLAC). DCN extension can be implemented over an out-of-band network, or the General Communications Channel (GCC) provided by the G.709 overhead present on a provisioned wavelength.

    Selection and deployment of the Cisco ONS 15454 counter- and co-propagating Raman units depend on the requirements of the network. The Cisco Transport Planner optical design tool is available to assist in the engineering, design modeling, bill-of-materials (BoM) generation, and deployment of the DWDM network.

    Both units incorporate faceplate-mounted LEDs to provide a quick visual check of the operational status of the card. Printed on each of the faceplates is an icon, an orange circle, which is mapped to shelf-slot icons indicating the shelf slot where the card can be physically installed.

    Using the counter- and co-propagating amplifiers, the Cisco ONS 15454 MSTP can support numerous applications, including the following.

     Support for very long single spans: The primary application of these high-power Raman amplifiers is to provide distributed amplification in very long single spans. The counter- and co-propagating units can provide high capacity over very long fiber spans where intermediate amplification or regeneration cannot be supported (such as repeaterless submarine links or festoon applications). Up to 155-mile (250-km) single-span systems are possible using 10-Gbps and 40-Gbps wavelengths. Using 100-Gbps wavelengths, the single-span reach of the system can be extended to approximately 130 miles (210 km). The maximum single-span reach attainable by employing Raman amplification with up to 8 channels, using both units, is 61dB.

     Ultra-long-haul unregenerated transmission: The high power counter-propagating units can be used in conjunction with EDFA-based optical amplification to extend the unregenerated reach of DWDM systems by preserving optical signal-to-noise ratio (OSNR) as multiple spans are traversed, allowing for systems up to 2000 miles (3200 km) in length.

     Improved transmission reach and capacity for networks with long spans: Many DWDM networks are deployed in locations where excessively long spans exist because of the geography of the region. EDFA-based systems suffer a high OSNR degradation when the wavelengths cross these long spans because of their high attenuation and tilt. Selective use of Raman amplification can lower the insertion loss of these spans and improve the overall unregenerated distance and system capacity.

     Expansion of system capacity to 96 channels: These Raman amplifiers, in addition to the Enhanced C-Band 96-Channel EDFA Amplifiers, support up to 96 channels in the C band, allowing 50-GHz systems to reach 9.6 Tbps of capacity with 100-Gbps wavelengths.

     Upgrade of transmission systems to higher per-channel bit rates: Increasing the bit rate of the wavelengths in the system typically creates the need to guarantee a higher OSNR for these wavelengths. As systems transition to 100-Gbps (and greater) wavelengths, Raman amplification can be selectively deployed to improve overall system performance and allow the upgrade of existing systems to higher per-wavelength bit rates.

     Reduced latency of storage-area-network (SAN) services: The higher OSNR achieved by selective use of Raman amplifiers in the DWDM network supports the possible avoidance of Forward Error Correction (FEC), reducing end-to-end latency.

    To equalize the Raman gain ripple, the high-power Raman amplifiers must be equipped in nodes with equalization ability: either a dynamic gain-equalizer (DGE) node or a reconfigurable optical add/drop multiplexing (ROADM) node. Multiple options are possible and are detailed in Figures 4 through 6.

    Figure 4. Equalization Stage with WSS (Wavelength Selective Switch) or WXC (Wavelength Cross Connect) and Counter-and Co-Propagating Raman Amplifiers

    Figure 5. Equalization Stage with Single-Module ROADM 1 (SMR-1) and Counter-and Co-Propagating Raman Amplifiers

    Figure 6. Equalization Stage with SMR-2 and Counter- and Co-Propagating Raman Amplifiers

    Product Specifications

    Tables 2 through 6 provide the specifications for the Cisco ONS 15454 High-Power Counter- and Co-Propagating Raman Amplifiers.

    Table 2. Regulatory Compliance

    ANSI (SONET) System

    ETSI (SDH) System

    Countries Supported

     United States
     Latin America
     Asia Pacific
     Middle East and Africa

    EMC (Class A)

     ICES-003 Issue 4 (2004)
     GR-1089-CORE, Issue 4 (Type 2 and Type 4 equipment)
     GR-1089-CORE – Issue 03 (Oct 2002) (Objective O3-2 – Section 3.2.1 – Radiated Emissions requirements with all doors open)
     FCC 47CFR15, Class A subpart B (2006)
     EN 300 386 v1.3.3 (2005) and v1.4.1 (2007)
     CISPR 22 – Fifth edition (2005-04) Class A and the amendment 1 (2005-07)
     CISPR 24 – First edition (1997-09) and amendment 1 (2001-07) and amendment 2 (2002-10).
     EN 55022:1998 Class A – CENELEC Amendment A2:2003
     EN 55024:1998 – CENELEC Amendment A1:2001 and Amendment A2:2003
     Resolution 237 (Brazil)
     VCCI V-3/2006.04
     EN 61000-6-1:2001
     EN 61000-6-2:1999


     UL/CSA 60950 -1 First Edition (2003)
     GR-1089-CORE, Issue 4 (Type 2 and Type 4 equipment)
     UL/CSA 60950 -1 First Edition (2003)
     IEC 60950-1 (2001/10)/Amendment 11:2004 to EN 60950-1:2001, 1st Edition (with all country deviations)


     GR-63-CORE, Issue 3 (2006)
     ETS 300-019-2-1 V2.1.2 (Storage, Class 1.1)
     ETS 300-019-2-2 V2.1.2 (Transportation, Class 2.3)
     ETS 300-019-2-3 V2.1.2 (Operational, Class 3.1E)
     EU WEEE regulation
     EU RoHS regulation

    Optical Safety

     EN or IEC-60825-2 Third edition (2004-06)
     EN or IEC 60825-1 Consol. Ed. 1.2 – incl. am1+am2 (2001-08)
     21CFR1040 (2004/04) (Accession Letter and CDRH Report)
     IEC-60825-2 Third edition (2004-06)
     ITU-T G.664 (2006)


     Acoustic noise
     GR-63-CORE, Issue 3 (2006)
     ETS 300 753 ed.1 (1997-10)
     Rain, sand, dust, and moisture proofing
     AS 1939-1990, 4.2, IP 53
     Mechanical shock and bumps
     AS1099- 2.27
     Customer-specific requirements
     AT&T Network Equipment Development Standards (NEDS) Generic Requirements, AT&T 802-900-260
     SBC TP76200MP
     Verizon SIT.NEBS.NPI.2002.010

    Table 3. System Requirements


    Cisco ONS 15454 M6

    Cisco ONS 15454 M2




    Shelf assembly

    15454-M6-SA shelf assembly with FTA2

    15454-M2-SA shelf assembly with FTA2

    System software

    Release 9.3 ANSI/ETSI or later

    Release 9.3 ANSI/ETSI or later

    Slot compatibility

    Slots 2 through 7

    Slots 2 through 3

    Table 4. Card Specifications




    Card LEDs

     Failure (FAIL)
     Active/standby (ACT/STBY)
     Signal fail (SF)



    Green /yellow


    General Specifications

    General power drawn





    Weight (not including clamshell)

    3.17 lb (1.44 kg)

    Optical connectors

    Cisco ONS 15454 High-Power Counter-Propagating Raman Unit (15454-M-RAMAN-CTP)

     Two LC-LC 2m cables to connect to or from COM Rx or COM Tx
     Two ES 2000 PS PC - LC 2m cables to connect to or from LINE Rx or LINE Tx

    Cisco ONS 15454 High-Power Co-Propagating Raman Unit (15454-M-RAMAN-COP)

     One ES 2000 PS PC 2m cable to connect to counter-propagating unit (15454-M-RAMAN-CTP)


    One slot


    Predicted mean time between failure (MTBF)

    15454-M-RAMAN-CTP: 182,263 hrs

    15454-M-RAMAN-COP: 110,854 hrs

    Operating Environment

    Continuous-operation air temperature

    32 to 140°F (0 to 60°C)

    Short-term operation air temperature per 96 hours per year

    23 to 158°F (–5 to 70°C)


    5 to 95% noncondensing

    Storage Environment


    –40 to 158°F (–40 to 70°C)


    5 to 95% noncondensing

    Transport Environment


    –40 to 158°F (–40 to 70°C)


    5 to 95% noncondensing

    Table 5. Optical Amplifier Specifications


    Counter-Propagating Unit

    Co-Propagating Unit

    Pump wavelength

    1428 nm (pumps 1 and 2)

    1457 nm (pumps 3 and 4)

    1428 nm (pumps 1 and 2)

    1457 nm (pumps 3 and 4)

    Raman pump unit class

    1 M

    1 M

    Operating range Raman pump power

    100 to 1000 mW

    200 to 1000 mW

    Maximum output power: pump laser 1+ 2 (1428 nm)

    500 mW

    550 mW

    Maximum output power: pump laser 1+ 2 (1457 nm)

    500 mW

    500 mW

    Pump-power set resolution

    0.1 mW (maximum)

    0.1 mW (maximum)

    Pump-power precision

    + or – 2%

    + or – 2%

    Optical power-settling time

    0.1 to 1 sec

    0.1 to 1 sec

    Maximum optical output power – LINE Rx port

    1200 mW (maximum)

    1200 mW (maximum)

    C-band signal wavelength range

    1500 to 1567 nm (96 channels)

    C-band wavelengths do not propagate through this card.

    C-band ripple



    0.5 dB (maximum)

    Insertion loss

     LINE-RX to COM-TX (1500 to 1527 nm)
     LINE-RX to COM-TX (1527 to 1567 nm)
     COM-RX to LINE-TX (1500 to 1527 nm)
     COM-RX to LINE-TX (1527 to 1567 nm)
     LINE-RX to MON-TX


    1.75 dB

    1.5 dB

    1.75 dB

    1.5 dB

    0.6 dB (pump wavelength)

    22– 26 dB (C-band signals)


    Optical connectors back reflection

    –40 dB (maximum)


     COM-RX to LINE-TX
     LINE-RX to COM-TX


    0.2 dB (maximum)

    0.2 dB (maximum)


     COM-RX to LINE-TX
     LINE-RX to COM-TX


    0.15 ps (maximum)

    0.15 ps (maximum)

    C-band ripple

     COM-RX to LINE-TX
     LINE-RX to COM-TX


    0.5 dB (maximum)

    0.5 dB (maximum)

    Table 6. DFB Laser Specifications



    DFB wavelength

    1568.77 nm

    Operating-range DFB power

    –15 to 6 dBm

    Off-state DFB laser power

    –50 dBm

    DFB laser-set resolution

    0.1 mW (maximum)

    Optical power-settling time

    0.1 to 1 sec

    Maximum DFB laser power

    10 mW (maximum)

    DFB spectral width (–3 dB full bandwidth)

    5 MHz (typical)

    Brillouin suppression (on dispersion shifted fiber)

    12 dBm

    DFB section class


    Warranty Information

    Warranty information is available on Cisco.com at the Product Warranties page.

    Ordering Information

    To place an order, visit the Cisco Ordering Home Page and refer to Table 7. To download software, visit the Cisco Software Center.

    Table 7. Ordering Information

    Part Number



    High-Power Counter-Propagating, 1W optical pump output power, C-band, 96-channel 50-GHz Raman unit with 2 ES 2000 PS PC – LC 2m cables


    High-Power Co-Propagating, 1W optical pump output power, C-band, 96-channel 50-GHz Raman unit with 1 ES 2000 PS PC 2m cable

    Additional Information

    Weight (Kg) 1
    Datasheet URL http://www.cisco.com/c/en/us/products/collateral/optical-networking/ons-15454-series-multiservice-provisioning-platforms/data_sheet_c78-658538.html
    Condition Refresh
    Module Type Optical Networking Module



    AED 0