SPIAD2431-16FXS-RF

Double click on above image to view full picture

Zoom Out
Zoom In

SPIAD2431-16FXS-RF

Description:

Cisco Refurbished
Original Part No : SPIAD2431-16FXS

Serv Prov IAD2431 w/16 FXS REMANUFACTURED
AED 0

Availability: Out of stock


Not Available

  • Add to Compare
  • Details

    This chapter provides a brief description of Cisco IAD2430 series integrated access devices (IADs) and contains the following sections:

    Overview

    Physical Description

    LEDs

    Chassis Grounding

    Memory

    Port Numbering Conventions

    Specifications

    Software Elements

    Interfaces and Service Capabilities

    Deployment Options

    Overview

    The Cisco IAD2430 series IADs aggregate multiple channels of data and voice or fax user-side traffic for transport over single or multiple WAN uplinks. Voice or fax traffic is transported by VoIP or by Voice over Asynchronous Transfer Mode (VoATM). All platforms support Media Gateway Control Protocol (MGCP), the signaling protocol H.323, and Session Initiation Protocol (SIP).

    The Cisco IAD2430, Cisco IAD2431, and Cisco IAD2432 series routers consist of five models with a common front panel (Figure 1). The Cisco IAD2435 series router consists of one model (Cisco IAD2435-8FXS) with a different front panel (Figure 2). The Cisco IAD2430, Cisco IAD2431, and Cisco IAD2432 series routers include a slot for the external flash memory card, as well as console, auxiliary, and flash (CF) memory ports. The front panel, labeled "Cisco IAD2400 Series," is identical for all models. However, the back panels, labeled by specific model number, vary considerably, depending on interfaces, ports, and options. Analog voice ports use an RJ-21 interface.

    Figure 1-1 Cisco IAD2430 Series IADs Front Panel

     

     

    Figure 1-2 Cisco IAD2435 Series IADs Front Panel

     

     

    The Cisco IAD2430 series IADs support the following interfaces:

    10/100BASE-T LAN connection

    T1/E1 port connections

    RJ-21 analog voice interface

    WAN interface card/voice interface card (WIC/VIC) options

    External/internal flash memory

    The Cisco IAD2430 series IADs can be mounted in a rack, on a wall, or a desktop.


    Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Statement 1015



    Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means by security. Statement 1017



    Warning No user-serviceable parts inside. Do not open. Statement 1073



    Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040


    Cisco IAD2430-24FXS IAD

    The Cisco IAD2430-24FXS IAD provides 24 analog foreign exchange station (FXS) ports with two 10/100BASE-T ports. The chassis (Figure 1-3) has the following interfaces:

    RJ-21 analog voice interface

    Two 10/100BASE-T ports

    External flash memory slot

    AC and DC power inputs

    Figure 1-3 Cisco IAD2430-24FXS Chassis

     

     

    Cisco IAD2431-8FXS IAD

    THe Cisco IAD2431-8FXS IAD (Figure 1-4) provides eight analog FXS ports, two 10/100BASE-T ports, and one T1/E1 WAN port. The chassis has the following interfaces:

    RJ-21 analog voice interface

    One T1/E1 port

    One 10/100BASE-T port

    One WIC/VIC slot

    External flash memory

    AC and DC power inputs

    Figure 1-4 Cisco IAD2431-8FXS Chassis

     

     

    Cisco IAD2431-16FXS

    The Cisco IAD2431-16FXS IAD (Figure 1-5) provides sixteen analog FXS ports with two 10/100BASE-T ports and two T1/E1 WAN ports. The chassis has the following interfaces:

    RJ-21 analog voice interface

    One T1/E1 port

    Two 10/100BASE-T ports

    One WIC/VIC slot

    External flash memory

    AC and DC power inputs

    Figure 1-5 Cisco IAD2431-16FXS Chassis

     

     

    Cisco IAD2431-1T1E1 IAD

    The Cisco IAD2431-1T1E1 IAD (Figure 1-6) provides one T1/E1 connection to a PBX, one T1/E1 WAN port, and two 10/100BASE-T ports. The chassis has the following interfaces:

    Two T1/E1 ports

    Two 10/100BASE-T ports

    One WIC/VIC slot

    External flash memory

    AC and DC power inputs

    Figure 1-6 Cisco IAD2431-1T1E1 Chassis

     

     

    Cisco IAD2432-24FXS IAD

    The Cisco IAD2432-24FXS IAD (Figure 1-7) provides 24 analog FXS ports, two 10/100BASE-T ports, and two T1/E1 WAN ports. The chassis has the following interfaces:

    RJ-21 analog voice interface

    Two T1/E1 ports

    Two 10/100BASE-T ports

    One WIC/VIC slot

    External flash memory

    AC and DC power inputs

    Figure 1-7 Cisco IAD2432-24FXS Chassis

     

     

    Cisco IAD2435-8FXS IAD

    The Cisco IAD2435-8FXS IAD (Figure 1-8) provides eight analog FXS ports, two Fast Ethernet ports, and one T1/E1 WAN port. The chassis has the following interfaces:

    RJ-21 analog voice interface

    One T1/E1 port

    Two Fast Ethernet ports

    AC and DC power inputs

    Figure 1-8 Cisco IAD2435-8FXS Chassis

     

     

    Physical Description

    Figure 1-9 and Figure 1-10 show the function options of the two IAD243x chassis. All interface slots are on the back of the chassis.

    Figure 1-9 Cisco IAD2430 Series IAD Back Panel Function Options

     

     

     

     
    1

    Chassis ground connection

    2

    RJ-21 connector

    3

    T1/E1 port 1

    4

    T1/E1 port 0

    5

    Flash memory slot

    6

    WIC/VIC slot

    7

    10/100BASE-T port 1

    8

    10/100BASE-T port 0

    9

    AUX port

    10

    Console port

    11

    DC power input1

    12

    On/off switch

    13

    AC power input

           

    1 This is not a redundant failover power supply connection. You must use either DC or AC.

     

     

    Figure 1-10 Cisco IAD2435 Series IAD Back Panel Function Options

     

     

     

     
    1

    RJ-21 connector

    2

    T1/E1 WAN uplink

    3

    Fast Ethernet port 1
    Fast Ethernet port 0

    4

    Serial port—console or auxiliary

    5

    Power connector

    6

    On/off switch

    7

    Chassis ground connection

    8

    Kensington security slot

       

     

     


    Note A Kensington security slot is located on the router back panel. To secure the router to a desktop or other surface, use the Kensington lockdown equipment.



    Note The FE built-in switch ports provide connections to 10/100BASE-T (10/100-Mbps) Fast Ethernet networks.


    LEDs

    The LEDs are located on the back panel of the Cisco IAD2430 series IADs. Figure 1-11 shows LEDs for the Cisco IAD2430 series IADs. The LEDs for the Cisco IAD2435 series IADs are located on the front of the chassis. Figure 1-12 shows LEDs for the Cisco IAD2435 series IADs.

    Figure 1-11 Cisco IAD2400 Series LEDs (Cisco 2432-24FXS shown)

     

     

     

     
    No
    LED/Color
    Description
    1

    ACT—green

    Status—green

    Green indicates activity—when any of the 24 voice ports is active in a call (off hook) or when one of the analog ports is in use

    Green when accessing IAD

    2

    CF (Slot 0)—green

    Green when accessing read or write function

    3

    Link—green

    100—green

    FDX—green

    Indicates link activity

    100BASE-T is active

    Green when full duplex is active, off when in half-duplex mode

    4

    ACT—green

    SYS—green

    PWR—green

    Blinking green during packet transfer and interrupts

    Blinking green for power-on and self-test, then solid green

    Solid green when system has power

     

     

    Figure 1-12 Cisco IAD2435 Series LEDs

     

     

     

     
    No
    LED/Color
    LED Color and Description
    1

    PWR OK—green

    Off—no power
    Steady on—normal operation
    Slow blink—boot up phase or in ROMMON monitor mode

    2

    FE ports 0/1—green

    Off—No link
    Steady on—link
    Blinking—TXD/RXD data

    3

    T1/E1 (carrier detect)—green

    T1/E1 AL—Amber

    Off—no Carrier Detect
    Steady on—Carrier Detect
    Off—no Alarm condition
    Steady on—Alarm condition

    4

    FXS ports 0 through 7—green

    Off—On hook
    Steady On—Off hook

     

     

    Chassis Grounding

    Chassis grounding is provided through the power cable, which uses a standard grounding plug. The chassis is also equipped with two 4 x 0.7 screw terminals for chassis grounding. The accessory kit contains a crimp-type ground lug that attaches to the two screw terminals. For more information, see the "Installing the Ground Connection" section on page 3-14.

    Memory

    The Cisco IAD2430 series routers contain flash memory and main memory.

    Onboard flash memory contains the Cisco IOS software image, boot flash contains the ROMMON boot code, and counterfeit prevention contains the cookie configuration.

    The default flash memory for the Cisco IAD2430 series IADs is 128 MB. Onboard CPU memory is 256 MB.

    Port Numbering Conventions

    Port numbering conventions for Cisco IAD2430, IAD2431, and IAD2432 series IADs are as follows:

    An external flash memory card is numbered CF 0.

    The 10/100BASE-T ports are numbered 10/100BASE-T 0/0 and 10/100BASE-T 0/1, from right to left.

    The T1/E1 ports are numbered T1 1/0 or E1 1/0 and T1 1/1 or E1 1/1, from right to left.

    The slot for WICs and VICs is numbered slot 0. WIC and VIC interfaces are numbered by interface with this slot number and an interface number, beginning with 0 and numbered from right to left.

    FXS voice port numbering begins at 2/0 and extends to 2/7, 2/15, or 2/23, depending on the number of voice ports.

    Port numbering conventions for the Cisco IAD2435 series IAD are as follows:

    Fast Ethernet ports are numbered 0 and 1, from left to right.

    The controller T1/E1 port is numbered T1 0 or E1 0, from left to right.

    FXS voice port numbering begins at 0 and reaches a maximum of 7, depending on the number of voice ports, from left to right.

    Specifications

    For the Cisco IAD2430 series hardware and electrical speicfications, see the Cisco IAD2430 series data sheets at the following URL:

    http://www.cisco.com/en/US/prod/collateral/voicesw/ps6790/gatecont/ps887/ps5321/product_data_sheet09186a008019aded.html

    Software Elements

    The operating system for the Cisco IAD2430 series IADs is the Cisco IOS software that resides in flash memory.

    Software Images

    Images c2430-is-mz and c2430-ik9o3s-mz can be loaded on the following platforms which have T1E1 and VWIC ports:

    IAD2431-8FXS

    IAD2431-16FXS

    IAD2431-1T1E1

    IAD2432-24FXS

    Images c2430-i6s-mz and c2430-i6k9o3s-mz should be loaded on the IAD2430-24FXS, which does not have a VWIC slot.

    Configuration Connections

    You can use an ASCII terminal or a PC to configure a Cisco IAD2430 series IAD. The configuration can be performed in several ways:

    Locally, with a direct connection through the serial port

    Remotely, with a connection through the serial port and a modem

    Through Telnet and TFTP

    Configuration Methods

    You can configure a Cisco IAD2430 series IAD automatically using the Simple Network-Enabled Auto-Provision (SNAP) option, or you can configure theCisco IAD2430 series IAD manually using several methods listed in "Manual Configuration" section.

    Automated Configuration

    If your Cisco IAD2430 series IAD was ordered with the SNAP option, no on-site configuration is required. When the Cisco IAD is powered on and connected to the WAN, the SNAP application downloads the applicable configuration files automatically. For additional information about SNAP, see the following URL:

    http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t8/ftapiad8.htm


    Note The SNAP option is not available on the Cisco IAD2435 IAD.


    Manual Configuration

    When you install a Cisco IAD2430 series IAD, see the "Power-On Procedure" section on page 4-1 for the initial configuration. This configuration sets the basic communication parameters. After the Cisco IAD is operating and able to communicate, use the procedures in the Cisco IAD2430 Series Software Configuration Guideto configure the specific services and functions, or to make changes to the existing configuration.

    You can use any of several manual methods for configuring a Cisco IAD2430 series IAD:

    System configuration dialog

    Configuration mode—Cisco IOS software command-line interface (CLI)

    setup command facility—Remote configuration through a LAN or WAN

    SNMP-based application—CiscoView or HP OpenView

    HTTP-based configuration server—Provides access to the CLI from a web browser

    Interfaces and Service Capabilities

    Table 1-1 describes the various physical ports and the services that each port type supports, including the following.

    Two administrative ports—One console and one auxiliary.


    Note The Cisco IAD2435 IAD provides a connection to the terminal or PC for software configuration or troubleshooting. The console port may be configured as a virtual auxiliary port for dial backup and remote management.


    One or two 10/100BASE-T LAN ports.

    One or two Fast Ethernet ports.

    The Cisco IAD2431 and Cisco IAD2432 IADs for a T1/E1 WAN interface are equipped with one or two T1/E1 WAN ports.

    Cisco IAD2430 series IADs for an analog voice user interface are equipped with an RJ-21 port for connection to a distribution panel.

    Cisco IAD2432 IADs for adigital voice user interface are equipped with a T1/E1 port for connection to a PBX.


    Caution All Cisco IAD2430 series IADs are customer premises equipment (CPE) only.

     

    Table 1-1 Cisco IAD2430 Series Interfaces and Service Capabilities 

    PortInterface ConfigurationsInterface ToServices SupportedDetails

    Console
    port 0/0

    EIA/TIA-232 asynchronous serial (DCE)

    ASCII terminal

    Personal computer

    Local administrative access

    RJ-45 physical interface

    Note The serial port on the Cisco IAD2435 acts as either console or auxiliary.

    Auxiliary
    port 0/1

    EIA/TIA-232 asynchronous serial (DTE)

    Modem

    Remote administrative access

    Data backup

    RJ-45 physical interface

    Note The serial port on the Cisco IAD2435 acts as either console or auxiliary.

    Fast Ethernet
    ports 0/0, 0/1

    10/100BASE-T (802.3)

    LAN

    Data

    RJ-45 physical interface

    RJ-21—8, 16, or 24 analog FXS voice ports

    Ports 2/0 to 2/23

    Ports 0 to 7 (IAD2435 only)

    FXS (loop-start or ground-start)

    Analog phone, fax, or modem

    Network side of key system

    Network side of analog PBX

    Analog voice/fax or modem

    Provides battery

    RJ-21 physical interface

    8-port FXS, on premise only

    16-port FXS, on premise only

    24-port FXS, on premise only

    T1/E1 trunk
    ports 0,1

    Channelized T1/E1

    WAN

    Carrier network

    Service types:

    ATM

    Cisco HDLC1

    PPP

    Transport types:

    TDM2 trunk

    Leased lines

    Built-in CSU/DSU3

    T1.403-compliant

    RJ-48C/CA81A physical interface

    Supports as many as 24 DS0s

    WIC/VIC slot

    S0 (serial)

    HDLC-based data

    WAN

    Carrier network

    User equipment

    Cisco HDLC

    PPP

    VoIP over PPP

    Physical interfaces:

    EIA/TIA-232

    EIA/TIA-530/530A

    EIA/TIA-449

    V.35

    X.21

    CF4 Slot 0

       

    Flash memory

    Flash memory card

    1 HDLC = High-Level Data Link Control

    2 TDM = time-division multiplexing

    3 CSU/DSU = channel service unit/data service unit

    4 CF = Flash memory

     

     

    Configuration Options

    The following interface options are available in Cisco IAD2430 series IADs:

     

    Table 1-2 Configuration Options

    Cisco IAD2430 SeriesRJ-21 1 T1/E1 2 FE 3 WIC/VIC 4 CF 5

    IAD2430-24FXS

    Yes

    None

    2

    N/A

    External

    IAD2431-8FXS

    Yes

    1

    1

    Yes

    External

    IAD2431-16FXS

    Yes

    1

    2

    Yes

    External

    IAD2431-1T1E1

    No

    2

    2

    Yes

    External

    IAD2432-24FXS

    Yes

    2

    2

    Yes

    External

    IAD2435-8FXS

    Yes

    1

    2

    N/A

    N/A

    1 Analog voice interface.

    2 T1/E1 ports.

    3 10/100BASE-T ports.

    4 WAN interface card (data); voice interface card (voice).

    5 Flash (CF) memory.

     

     

    Deployment Options

    Figure 1-13 through Figure 1-16 show some typical deployment scenarios for the Cisco IAD2430 series integrated access devices (IADs).

    Figure 1-13 Analog FXS User Interfaces with Metro Ethernet WAN Interface

     

     

    Figure 1-14 T1/E1 WAN Interface with Analog FXS User Interfaces

     

     

    Figure 1-15 WAN Interface with Analog FXS and FXO User Interfaces

     

     

    Figure 1-16 T1/E1 with T1/E1 Interface to PBX

     

    Additional Information

    SKU SPIAD2431-16FXS-RF
    Weight (Kg) 1
    Datasheet URL http://www.cisco.com/c/en/us/td/docs/routers/access/iad2400/2430/hardware/installation/guide/hw_inst/2430ovw.html#wp1045863
    Condition Refresh
    Module Type Integrated Access Device

    SPIAD2431-16FXS-RF

    AED

    AED 0

    0